• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Replacement UPVC Door handles for bifold doors

Find the perfect handle for your door, whether replacing your existing handles or adding extra security. Upvc handles are simple to install and conform to the required 92mm centres of multipoint locks.

The most important measurements to consider are the backplate fixing centers and key hole dimensions for levers and levers. Make sure you compare these to your current measurements prior to ordering.

Lever/Pad

Lever pad handles consist of a lever on one side and a handle that is shaped like a paddle on the opposite. These are designed to be used with key wind locks, however, they can also be used to split spindle multipoint door locks (though you will need an additional dual spindle lock case).

Once you have chosen the correct handle for the doors the finishes will be listed in the drop-down list. Certain styles of handles are not available in all finishes. It is recommended to look over the technical drawings and size sections for the specific item you are looking to ensure that you get the right size and fit.

When selecting new lever pad door handles made of upvc, it is essential to ensure that they are in line with the PZ (distance between the spindle of the handle and the centre of the hole in the cylinder) of your existing multipoint locks, as these need to be in line to ensure that the doors remain locked, either from the inside or the outside. Our window handles for upvc replacement door handles - extra resources - are designed to fit a wide range of standard cylinders, but it is a good idea to double-check before ordering.

You will need to remove your handles that you have already installed and then dismantle the lock case if you are upgrading to dual spindle handle levers since this will require a split inline cylinder. You can purchase these separately. We have included a technical illustration in the images of each product.

It is a good idea to loosen the screws that hold your existing door handle and then check the mechanism. If the screws aren't tight enough then you might need to loosen them even more. Then you can remove the spindle from the door handle and replace it with a new upvc handle. Before you screw the handle into the frame, it is a good idea to ensure that it is in the right position, and you can do this by inserting your finger in the gap between the door frame and the handle to ensure that it is in a level position.

Lever/Lever

The lever door handles are used to operate a multi-point lock that uses an Euro cylinder. They can be found on many upvc double doors, as well as on some wooden and aluminum doors. They come in two forms, having a lever on the interior and a paddle outside. Sprung - They have an internal spring cassette within the backplate to help to bring the handle lever into an upright position. Non-sprung - These do not include a spring mechanism and will require manual pulled to raise the handle lever back to its horizontal position.

To fix the door handle of a lever that is sagging, you will need to find the hole for access to the detent or pin, which is typically a small round or rectangle shaped hole or protruding pin located on one side of the base plate. Once located you can loosen the set screw with the help of a screwdriver, and then take it off to allow the lever to return to its horizontal position.

After the handle is set horizontally, it is possible to put back the screws. Tighten them to ensure that the handle is securely connected to the base plate. It is also recommended to apply a threadlocking adhesive solution to the screw threads to increase the grip and prevent them from becoming loose over time.

Lever door handles that droop can be caused by various causes. The most common reason is that the fixings have been too tightened and are putting strain on the bearings of the lever, which causes it to become a bind on the door face. It could also be due to the fact that the levers aren't operated at a straight angle and this is causing the latch mechanism and preventing it from fully springing back into service.

The most common reason for spring levers that are not functioning properly is that the spring is not being in the right position on the backplate. The most effective way to determine this is to operate the handle to see if it returns to the horizontal position.

It is crucial to fix any patio door handle replacement handles that are loose immediately. This can cause excessive wear on the screws and the handle may even be able to fall off the base plate. It is also recommended to tighten loose screws frequently to stop them from becoming looser.

Lever/Snib

These upvc door handles are also referred to as 'Snib' handles and have a snib lever towards the top of the lever that you can press down to lock your door in the event that you don't have a fake lock. These door handles are fitted with the Fullex lock 68PZ. (68mm between spindle and the centre of the lock). We also stock a variety of other door handles with 68PZ from various manufacturers, including Ferco and Fab & Fix.

You can update your home by changing your door handles, whether you are replacing your existing handles or installing new ones on doors that you have constructed. There are many styles of door handles made of upvc with traditional levers on backplates, straight or curved short latches and dummy knob handles for multi point locks that are perfect for French doors.

Rose door handles are oval or circular versions of lever on backplate handles. These kinds of door handles are equipped with an a knob or lever on a backplate that sits behind the knob or lever and is sometimes called the rosette, however certain back plates can be removed to allow for concealed fixing.

These handles are available in a variety of finishes including coloured and chrome finishes, to be matched to your door and hardware like knobs, bolts and hinges. Some handles come with grub screws, which assist in firmly attaching the knob or lever to the spindle. Some handles come with bathroom spindles that are suitable for bathroom locks. They also come with a thumbturn release mechanism and can be used on doors for bathrooms.

Mortise

If your uPVC front door handle is stuck in the open position, the problem will most likely be with the tubular latch. There may be a few reasons for this, the most common being a simple lack of lubrication on the latch plate. It is possible to fix this issue by opening the door, spraying lubricant onto the handle and locking. It could also be that the latch plate is separated from the backplate. This could be more of a problem and would require a professional to fix it.

A multipoint handle system is the ideal solution to a stuck door handle. These handles are mounted through the faceplate and are operated by either a thumb turn or key knob that activates the cam that locks the deadbolt. The handles are available in different sizes to suit different types of uPVC doors and are available in various attractive finishes that are compatible with existing hardware. The handles can be purchased online or through the local locksmith and can be installed with clear instructions.

You will need to know the PZ size of your cylinder in order to select the right replacement handle set. This is the measurement in millimetres between the inner edge of the frame of the door and the centre of the hole for the handle. You will also need to know if your door has hook locks or a mortise-style lock. Once you have these measurements, the simplest way to find the correct handles is to filter by brand on the website. This will narrow down your choices and allow you to select the correct size from there.

A typical handle set includes the handle and a pair of different length screws as well as drill guides and installation instructions. The smarter models, like the Igloohome Smart Mortise 2+, include an entire mortice lock that has built-in keypad. These are more complicated units that are best suited to professional installers or highly competent DIYers. Certain handle sets come with an array of other accessories, such as weather strips that can be used to enhance the appearance of the door.