• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

The first protection is your door lock. It can stop unauthorised access to your home. The signs of wear and tear as well as instances like moving into a new residence or break-ins, can necessitate the need to replace door lock (visit your url) your lock.

To begin, you must determine the size of your cylinder by measuring the distance between the adjustment screw and the middle of the cylinder knob. This measurement will allow you to buy the right lock.

Deadbolt

If you're looking to ensure that your door is secure against intruders, it's a good idea to install deadbolts. When the bolt is extended into the strike plate of the doorframe, it makes it harder for an intruder through the door. A single-cylinder deadbolt can be activated with a key on the exterior, and a thumb-turn device that is located inside. Deadbolts are only effective if it's installed correctly, though.

First, you will need to determine if the door already has a hole to install deadbolts, or if it needs to be bored out. With the template included with the lock installation kit mark the location of the hole for the deadbolt on the door's surface. Then, you can use your tape measure to determine how high the deadbolt should be. Mark this measurement on the door's edge, and then use a speedsquare to draw a straight line across the mark you made for the bolthole.

Next, use a power drill to bore out this spot until the hole extends to the opposite side of the door. This could take a while. Then, sand the hole and the edges of the door until it's smooth. At this point, it's a good idea also to paint or stain your composite door lock replacement.

Remove any screws that are visible from the deadbolt. This will reveal the front and rear assembly of the deadbolt as well as its bolt inside. Then, remove the bolt and replace it by the new bolt to match your door hardware. The bolt is often connected to a set plate that you need to unbolt. After this, you'll need to chisel the door frame to accommodate the strike plate.

If your strike plate is not aligned it's likely that the previous installer didn't correctly mortise it or a weatherstripping was installed and changed the strike position. It is necessary to re-mortise your strike plate and perhaps even the deadbolt to fix this issue. Once this is completed check the deadbolt by closing and locking it. Be sure the bolt extends into the strike plate then test the key to make sure it opens and closes effortlessly.

Knob

When a door knob is worn out it could make your home or business less secure. It may make it more difficult to open or close the door, so it's recommended to replace it. It shouldn't take longer than 30 minutes. You can use a screwdriver or pliers to take off the knob or handle, but be careful not to harm any of the other components on the door.

Before you begin, you'll want to spray WD-40 or another dry lubricant on the mechanism of the knob on your door. This will help the new lock to move smoothly when you turn it. It's essential to select the best knob and handle that matches your doors currently in order to ensure that the lock is operating properly. If you don't have a matching doorknob, you will need to purchase a replacement upvc door lock.

Before you begin replacing the knob, examine the old knob to see what screws are that are holding it in place. If there are no screws then you can use the screwdriver to secure the cover plate into the screws plate that is hidden.

After taking the knob off take it apart and look for evidence of damage or rust. You'll have to scrub it off if you notice any scratches or marks, but you shouldn't have to do anything when the knob is in good condition.

Now is the time to put in the new one. It is important to first look over the two knobs to ensure that you've chosen the correct one for your door. You'll need to select one with an extending rod that locks with the rod mechanism of the other knob. Once you've put the new knob into the hole, slide it into the latch.

Thread the latch plate screws down and test the spring by pressing down several times. The latch should then spring back up each time. Install the second knob, and lock it to the rod mechanism of the first knob. Thread the long screws from the interior doorknob through the holes for the cylinder on the outside knob and fix it in its place.

Latch

A latch is a piece metal that extends into the door jamb to keep it closed. The latch is operated by a handle or knob on the interior of the patio door locks replacement, or by a thumb-turn on the outside. The latch can be secured by deadbolts to stop thieves from breaking through the glass of the door. It can also guard against intentional or accidental closing by pets or children. You can install an entry point with either a single-cylinder or double-cylinder deadbolt, depending on the level you prefer for security.

Installing a latch requires the same steps similar to installing a deadbolt however there are some variations. To ensure that the new lock will fit first, measure the setback on the doorjamb with an instrument such as a tape measure. The setback is the distance from the edge of the doorjamb to the center of the hole for the faceplate of the latch. The standard setback is 2 3/8 to 2 3/4 inches. If you have a higher setback, Replace Door Lock you might need to purchase a longer latch from a hardware store or locksmith.

Then, you'll need to make a hole for a latch plate in the edge of the doorjamb. Utilize a chisel to make the mortise for the latch. Make sure that the depth is enough for the faceplate to be in line with the doorjamb. Place the strike plate in the correct position to ensure it is positioned correctly.

If the strike is positioned too high, the door can be pushed in or pressure put on it using a crowbar, or tire iron. This could also cause cracks in the doorjamb. To fix this, the strike can be lowered by drilling a new hole through the doorjamb, and then chiseling out the core of the old hole.

The final step is to install the new strike plate, which can be done by screwing it over the existing screw holes. Then, use wood putty to cover the holes from the previous screws and the bolt hole that will not be used. After the putty has dried then sand it to a smooth finish for an elegant finish.

Strike

The piece of metal that is inserted between the latch and deadbolt when the door is closed is an electric strike. It is a vital part of the lock's overall safety, as it prevents the door from opening and gives an additional level of resistance to force or kicking. If a door is fitted with an electronic strike, it can be opened only by a key and the control unit that regulates its electrical impulses.

Traditionally the installation of an electric strike required cutting a section of the doorjamb to remotely release the latchbolt of a cylindrical lock from the pocket of the strike. This modification is not just ugly, but also exposes the mechanism for the latchbolt and the keeper to intruders.

Recently, several electric strike makers have come up with a brand new electric strike, dubbed the "No Cut" strike that doesn't require an opening in the doorjamb to operate. The strikes use a unique design that allows the latchbolt and keeper to slide into the strike pocket without marring the faceplate of the doorjamb.

The strike has an internal ramp that raises the latchbolt and keeper when it receives an electrical signal from a reader or controller. The latchbolt and keeper are pushed higher up the ramp due to retraction. When the upvc door locks replacement is closed the deadbolt remains in at a lower position and the latchbolt retracts into the keeper.

Installing an electric strike can be a simple process, especially if you are replacing an existing strike door. If you are upgrading an access control system to an electric strike, it is important to ensure that the new system is compatible. You will also have to ensure that the strike is properly connected to your access control system and is set up to operate in a safe manner.

Upgrade your strike plates to heavy duty strike plates to block unauthorized entry. These plates are fitted with four to six three-inch screws instead of the two, three-fourth inch screws commonly used in standard strikes. These screws are longer and make breaking the frame to reach the thumb turn piece on a single deadbolt cylinder more difficult.